DAISY CO2 200 MANUAL HOW TO
DAISY CO2 200 MANUAL FREE

This design was pushed as a seal-less design and said it didn't need o-rings but after my tare down it looked like the seal they had in the CO2 puncture needle was no longer capable of retaining the pressure. Always double check when replacing a spring that the new one doesn't hinder the function of the device. But some instances could require a spring that has a specific strength. From what I can tell it is just needed to push the trigger mechanism down. If it is then I will just cut it to a shorter length. It was a little longer but it shouldn't be an issue. After looking through some of my pens lying around the house I found a spring in one of them that was about the right size to replace the old one. The spring that was bent and the broken seal. After this complete disassembly I found two potential causes that could be preventing this from operating. Now is the time to repair any of the issues that you discovered while tearing apart your project. I will need to find a replacement for this. Unfortunatly the spring was either bent during disassembly or prior to disassembly. Luckily it was pretty obvious and i found out where it went right away. I had to look things over tho figure out where this spring had to go for assembly. When I removed the main mechanism from the barrel assembly a small spring shout out. I had to remove the screws one by one and slowly disassemble this pistol. As a precaution I did my best to make sure that any possibility of retained pressure has been released. This pistol uses pressurized gas to propel a BB. I have received many cuts and shocks because I underestimated how I could be injured working on something. Many things that you may attempt to fix can have the potential to harm you in some way or another. Now before I take it apart there is something to think about. And the best way to remember how if went together is to take a lot of detailed pictures of every step for you to reference. When ever you take something apart you will need to put it back together. This is a little for your benefit but it is mostly for my own.

You will notice that I have a lot of pictures of every little step that I did. Now to see if this can be sealed or what is causing the problem. It quickly emptied the whole cartridge which if you don't now makes it very cold. I tightened the screw on the bottom that pushed the CO2 cartridge into the puncture needle and I was met with a loud hissing noise. It easily moved to the side which revealed the hole to insert the BBs. On the rear of the gun I noticed what looked like a small lever. Now that I had the CO2 inserted I needed to find where the BBs were loaded. There appeared to be a spacer that allowed the use of a smaller cartridge so I just removed that and inserted a new CO2 cartridge. Pulling on the indent popped the grip right off revealing where the CO2 cartridge needed to go. Upon looking it over I noticed a small indent on the bottom of one of the grips.

DAISY CO2 200 MANUAL HOW TO

This had no instructions so I had to look it over to get an idea on how to make this function.

I may be a perfectionist.Р”В«efore I could test this I needed to determine how it even functioned. Unless you happen to be like me where you want to tear it apart and clean everything and make it as close to new as possible. This is easy to do and if its just a quick fix like that then you just saved yourself a lot of time and effort. Sometimes it is as simple as replacing batteries or something like that. This is a very important step when you get something that is new to you. So, hopefully something in these steps might help you on your next attempted repair.Р”Вepending on your project you may need additional tools. I know most of you probably don't have this specific air pistol but in this instructable I want to cover what I did on this project along with some general tips that I use when attempting to repair anything.

DAISY CO2 200 MANUAL FREE

And I had a good amount of free time to troubleshoot repairs. But where there is a will there is a way. unfortunately this was designed as a 'seal-less' design that required no o-rings so often when they leaked they were trash. The model 200 was made from 1963 to 1976. It featured a 200 shot BB reservoir with a 5 shot spring loaded magazine. Upon research this model I found out this was a Daisy 200 semi auto CO2 pistol. He didn't want it any more so it was now mine but before I could plink away I would first need to make sure it was back in working order. Not too long ago I was looking around in my grandfather's garage when I stumbled upon this beauty.

Daisy co2 200 manual